Division 26 electrical specifications: what estimators should read
Division 26 is the part of the project manual that covers electrical work. Read it next to the drawings, because it holds requirements the plans often don’t show: how to install, what to submit, what to test and what to label. Every one of those requirements costs labor or material, so each one needs a home in your estimate.
This guide explains how the division is organized and which clauses estimators should read first. It uses one public example, so your project’s specs will differ.
What is Division 26 in a spec book?
Specs are organized using CSI’s MasterFormat. The Whole Building Design Guide’s SpecsIntact help page (page read in 2026) says MasterFormat is “used throughout the construction industry to format specifications for construction contract documents.” It says the information sits in 50 divisions, compared with 16 before 2004.
Source wbdg.org
An EC&M article from 2006 explains that MasterFormat 2004 split the old Division 16 into four divisions, 25, 26, 27 and 28. It titles Division 26 “Electrical and Lighting,” Division 27 “Communications” and Division 28 “Electronic Safety and Security.” Editions change titles over time, so use the numbers and titles in your own project manual.
On many jobs, the work you price is in more than one division. Our guide on reading electrical plans before an estimate lists Divisions 26, 27 and 28 together. Also read Division 01, General Requirements, which appears in the same WBDG list of divisions.
Which sections should you read first?
Owners publish their own versions. The University of Maryland posts its Division 26 contractor specifications (page read in 2026). Its sections include:
- 26 05 00, Common Work Results for Electrical
- 26 05 19, Low-Voltage Electrical Power Conductors and Cables
- 26 05 26, Grounding and Bonding for Electrical Systems
- 26 05 29, Hangers and Supports for Electrical Systems
- 26 05 33, Raceway and Boxes for Electrical Systems
- 26 05 48.16, Seismic Controls for Electrical Systems
- 26 05 53, Identification for Electrical Systems
- 26 05 73.13, 26 05 73.16 and 26 05 73.19, Short-Circuit Studies, Coordination Studies and Arc-Flash Hazard Analysis
- 26 09 13, Electrical Power Monitoring and Control
The page continues past these. The point is the pattern. The 26 05 sections cover common work results, so they are a good place to start. A clause there may affect the price of other sections, so check how the spec ties them together.
What clauses in the common sections change your price?
Read each section’s general, product and execution parts. In the Maryland example, the clause numbers show that structure, for instance 1.5 for coordination and 3.1 for common installation requirements. These are the kinds of clauses worth flagging, with examples from that spec:
- Installation standards. Section 26 05 00 requires compliance with “NECA 1,” and 26 05 33 says to comply with NECA 1 except where requirements on the drawings or in that article are stricter. Section 26 05 29 says that for EMT, IMC and RMC supports, NECA 1 spacing applies where its Table 1 gives shorter spacings than NFPA 70. Shorter support spacing means more hangers and more labor.
- Sleeves. Section 26 05 19 and 26 05 33 require sleeves for penetrations of concrete slabs and walls unless core-drilled holes or formed openings are used. Section 26 05 00 sizes sleeves to leave “1/4-inch annular clear space between sleeve and raceway or cable, unless indicated otherwise.”
- Firestopping. Section 26 05 00 says to “Apply firestopping to penetrations of fire-rated floor and wall assemblies,” per Division 07. Find out who furnishes and installs it before you assume it is yours or someone else’s.
- Timing of embedded work. Section 26 05 00 says sleeves, conduits and boxes must be set accurately “before any concrete is poured or partitions are erected.” That affects crew scheduling, not just material.
- Identification. Section 26 05 53 says to “Install identifying devices before installing acoustical ceilings and similar concealment.”
- Studies and seismic work. Short-circuit, coordination and arc-flash studies, and seismic restraints, have their own sections. In the seismic section, controls are “considered defective if they do not pass tests and inspections,” and each restraint device needs a delegated-design submittal.
We are not saying your spec has these clauses. We are saying to look for them.
How do you turn spec clauses into estimate lines?
A simple method works well on a long manual:
- Read the 26 05 sections first and highlight every clause that adds work, material, testing or paperwork.
- Write each one as a question or a line item. “Who sets sleeves before the pour?” is a good question. “Seismic restraints, per 26 05 48.16” is a good line.
- Match each clause to a drawing detail or a schedule. If the spec says one thing and the drawings another, send an RFI.
- Price the items that have no symbol on the plans, such as labels, studies, submittals and firestopping, so they do not slip through.
- List anything you exclude in your written clarifications.
- 1Read the 26 05 sections
- 2Highlight clauses that add cost
- 3Match each to a drawing or schedule
- 4Price it or write a question
- 5List exclusions in the bid
Our posts on electrical bid addenda and bid exclusions and clarifications cover the last steps. Spec changes often arrive by addendum, so re-read the division when one lands.
What if the spec and the drawings disagree?
They sometimes do. In the Maryland spec, 26 05 33 says to comply with NECA 1 “except where requirements on Drawings or in this Article are stricter.” In other words, the stricter requirement may win. Your contract’s order-of-precedence language decides, so read it, or ask the owner in an RFI before you bid. Do not guess when the difference moves the price.
How does this fit with the rest of the bid?
Specs feed the whole estimate. Labor units should reflect the installation method the spec requires, and our guide to electrical labor units explains how to adjust them. Assemblies are a good place to store spec-driven items such as hangers, supports and labels, as covered in electrical estimating assemblies. Before you submit, run the bid review checklist.
Where Amptake fits
Amptake is being built to count devices and fixtures on a plan set, show each count on the drawing and build a bid from your own labor units and supplier pricing. Reading the specification stays your job, because the clauses that move the price are written in words. Join the waitlist for early access.
This article is general information for estimators, not legal or engineering advice. Spec language varies by project, so check your contract documents and ask a qualified professional about anything unclear.