Electrical estimating assemblies: how to build one that prices right
An electrical assembly is a saved bundle of the parts and labor needed to install one thing, such as a duplex receptacle. You count the receptacles once and the software prices the box, device, plate, wire and labor for each. A good assembly saves hours on every bid. A bad one repeats the same error on every bid, so build it carefully and test it.
What is an assembly in an electrical estimate?
An assembly groups materials, labor and other costs into one reusable unit. zzTakeoff’s documentation says that when an assembly is applied to a takeoff, the software calculates all associated materials and costs. Its page was marked as being revised when we read it, so check your own software’s help for exact steps.
The idea is old. A 1998 article in Roads & Bridges, Assembly Estimating, describes it as production-based: it starts from a parts list and produces detailed lists of materials, labor, subcontract and equipment. That is different from unit-price estimating, which it calls cost-based. The same abstract notes that a formula may be needed because an assembly’s unit of measure does not always convert directly to its parts’ units.
Why use assemblies instead of counting every part?
- Speed. One count drives many line items.
- Completeness. The plate, the connectors and the labor do not get forgotten, because they are in the assembly.
- Consistency. Two estimators price the same device the same way.
- Easier price updates. In most programs, changing a part’s price once updates every future use.
The risk is the flip side. If the assembly leaves out a part, every bid leaves it out.
How do you build an electrical assembly?
PlanHub’s guide to creating an assembly shows a pattern most programs follow. You name the assembly and pick a measurement type (area, linear or count). You add cost items, give each a unit cost, a unit of measure and an optional waste percentage, and write a formula for every cost item. Then you save it and test it on a takeoff.
- 1Name it and pick the measurement type
- 2List every part and the labor
- 3Set units, waste and a formula for each
- 4Test it against a hand count
- 5Save it and review it on a schedule
Apply that to electrical work:
- Pick the unit you count. A receptacle assembly counts each. A conduit assembly counts feet. Match what you take off on the plans.
- List the parts. Include the small items: box, device, cover plate, wire connectors, support, fittings.
- Add labor. Pull the hours from your own labor units, not from a guess.
- Write the formula. The formula turns the count into a quantity of each part, such as one plate per device or one connector set per box.
- Set waste. PlanHub’s example shows that waste increases output, so 10 units with 10% waste becomes 11. Use your own waste rates and say where they came from.
What does an assembly look like? An illustrative example
Illustrative only. These are not real prices or labor units. A single-gang duplex receptacle on a wall in a commercial space might hold:
| Item | Formula | Note |
|---|---|---|
| Device | 1 per count | Check the spec grade |
| Box | 1 per count | Match the wall type |
| Cover plate | 1 per count | Color per finish schedule |
| Connectors | 1 set per count | Small items add up |
| Labor | your hours per count | Set for normal conditions |
| Waste | your percent | Applied per item |
Wire and conduit to the device are usually priced in a separate run assembly, because their quantity depends on distance, not on the device count. Say which assembly carries them, so they are counted once and only once.
How do you adjust labor in an assembly?
Labor in an assembly is only as good as the labor unit behind it. A published labor-unit book sets conditions. In an article on the NECA Manual of Labor Units, EC&M explains that the normal column applies when conditions permit the maximum productivity of electricians. He adds that most projects have conditions that require labor units to be adjusted, and that the labor increase from one column to the next is approximately 25%.
So build your assembly for normal conditions, then apply a factor for the job: a tall ceiling, an occupied building, a tight schedule. Do not bake difficulty into the assembly itself, or you will forget it is there. Our guide to electrical labor units covers how to use and adjust them.
How do you test an assembly before you trust it?
- Hand-count one device. List the parts on paper. Compare the list to the assembly output, line by line.
- Run a past job. Apply the assembly to a finished job and compare to what was actually bought and installed.
- Check units. Feet, each and boxes are easy to mix up. PlanHub’s guide suggests a formula test and rounding up when only whole boxes are bought.
- Look for stale prices. Material costs move. Our post on copper price swings shows why you should date your prices.
- Have a second person review it. A fresh eye finds the missing connector.
Common assembly mistakes
- Leaving out small items because they seem too minor to list.
- Counting wire in both the device assembly and the run assembly.
- Using a supplier’s price from last year.
- Mixing job difficulty into the base labor.
- Copying a vendor’s default assembly without checking it matches how your crews build. Default libraries are a starting point.
- Never reviewing assemblies after a code cycle changes. See the 2026 NEC changes post for what to check.
Where Amptake fits
Amptake is being built to count devices and fixtures on a plan set, show each count on the drawing and build a bid from your own labor units and supplier pricing. Whether an assembly is right for your crews stays your call. Join the waitlist for early access.
This article is general information for estimators, not engineering, legal or code-compliance advice. Check your own pricing, local codes and project documents before you bid.