All guides

How to estimate an EV charger installation: what to check before you quote

To estimate an EV charger installation, start with the electrical service, not the charger. Find out whether the panel has room for the added load, size the circuit and wire for a continuous load, price the run from panel to charger, and add the permit and inspection. The charger itself is usually the smallest unknown.

This guide is for estimators and owners at small electrical firms who quote Level 2 charger jobs. It uses public sources, and it is general information, not a substitute for the code or your inspector.

What does the site visit need to answer?

Most of the price is decided before you open a spreadsheet. Collect these facts on the visit or in a customer questionnaire:

  • Which charger? The U.S. Department of Energy says owners may install Level 2 (240 V) equipment for a faster charge (page viewed in 2026). Get the model and its nameplate current, because the circuit depends on it.
  • Plug-in or hardwired? This changes the parts list, and the receptacle rules below.
  • Main panel size and open spaces. Note the main breaker rating, the free slots and the panel’s condition.
  • Distance and route. Measure from the panel to the charger location, and note whether the run is in a finished wall, an attic, a garage or outdoors.
  • Who else is involved? Utility, landlord, HOA or property manager, and the local permit office.

For a commercial or multi-charger job, add the use case, the number of chargers and how long vehicles park. An EC&M report from 2023 says to gather this information first, and reports that a Level 2 charger is typically enough when vehicles park for long periods.

Does the building have enough capacity?

This is the question that turns a small job into a large one. The Department of Energy page says some homes might have insufficient electric capacity for Level 2 equipment, and that a qualified electrician can add circuits to supply the capacity.

The City of Palo Alto says most Level 2 chargers need 30 to 50 amps (page viewed in 2026). It adds that a home with a 100-amp panel may need an upgrade to 200 amps, and that a lower-powered charger drawing only 20 amps is an option where capacity is tight. Local rules differ, so treat that as an example, not a rule of thumb.

Permit offices often ask you to show the math. One example is Menlo Park, California’s 2021 residential EV charger guidelines. They include a service load worksheet where the charger’s wattage is the circuit’s amp rating times 240 volts, added to the other home loads. If the city’s table shows a larger minimum service than your existing main breaker, a larger service panel is required. Your own jurisdiction may use a different method, so ask first.

How do you size the circuit?

The NEC treats the charger as a continuous load. EC&M’s 2023 code article says “the NEC considers EV charging loads to be continuous loads” and that services and feeders must be sized per the product ratings. Read the charger’s installation instructions and the code edition your jurisdiction has adopted for the exact breaker and wire sizes.

As a local example, the Menlo Park guideline lists these minimum conductor sizes by breaker size (reproduced as published):

Breaker Minimum conductor EMT size
20 or 30 amp #12 ½”
40 amp #10 ½”
50 amp #8 ¾”
60 or 70 amp #6 ¾”

That table is from a California city under the California Electrical Code. Do not copy it into your estimate. Use it to see how cost steps up as the breaker grows, and confirm your own sizes against your adopted code.

What other code items change the price?

The same EC&M article lists several rules that add parts or labor:

  • Receptacles: every receptacle that connects EV supply equipment must be GFCI protected (Sec. 625.54).
  • Disconnect: equipment rated above 60 amps or over 150 volts to ground needs a readily accessible disconnect that can be locked open (Secs. 625.43 and 110.25).
  • Load management: where an automatic load management system is used, the maximum load on a service and feeder is the load that system allows (Sec. 625.42(A)).

Section numbers can shift between code editions, so check them against the edition in force where you work. The article does not name an edition.

The load management rule matters on larger jobs. A managed system may let you add chargers without upsizing the service, but it adds equipment and setup time. Price both options and show the customer the difference.

What do you add for permits and inspection?

The Department of Energy page says appropriate permits may be required from local building and permitting authorities. Menlo Park’s process, for example, asks for the manufacturer’s installation instructions and charger specifications with the permit application, followed by plan review, then an inspection after the work is done. Someone must be on site for that inspection.

Put permit fees, your time for the application, and the inspection visit on their own lines. Utility rebates and tax incentives change often. If you mention them to a customer, point to the program’s own page rather than quoting an amount from memory, and leave tax questions to the customer’s accountant.

A short estimate checklist

  1. Charger model, nameplate current, plug-in or hardwired.
  2. Panel rating, free spaces and condition.
  3. Load calculation in the format your permit office wants.
  4. Breaker and conductor size from the adopted code and the charger instructions.
  5. Run length, route, conduit type and any trenching or patching.
  6. GFCI, disconnect and labeling items.
  7. Permit, inspection and utility steps.
  8. Clear exclusions: panel upgrades, utility work, drywall repair and paint.

Where Amptake fits

Amptake is being built to read plan sets, count devices and fixtures against your legend, and build a bid from your own labor units and supplier pricing, with every count open for you to review. Join the waitlist.

This article is general information for estimators, not engineering, legal or code advice. Electrical codes and permit rules vary by location and edition, so confirm requirements with your authority having jurisdiction.